Oil

0 to 0 years Naukri Gulf

Electrical/Mechanical Technician

On-site - Morocco - Boulemane 17 July 2026

Engineering

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Perform safe and efficient preventive and corrective maintenance on Vestas V90 3MW wind turbines and Balance of Plant (BoP) assets in accordance with OEM requirements, ACWA OPERATIONS policies, and site safety rules, ensuring high availability and reliability of the wind farm.Key AccountabilitiesHealth, Safety, Security & EnvironmentStrictly comply with ACWA OPERATIONS policies and procedures, OEM safety instructions, and customer/site rules.Apply and maintain safe systems of work, including:Permit to Work (PTW),Lock Out / Tag Out (LOTO),Isolation & re-energization safety checks, andWorking-at-height, confined space, lifting operations controls (as applicable).Report all incidents, near-misses, unsafe conditions, and environmental spills/risks in line with ACWA OPERATIONS HSE policy.Maintain high standards of housekeeping in turbines, workshops, warehouses, and work areas.Maintain 5S in own work areas (turbine, workshop, warehouse staging) and ensure as-left condition after each task.Ensure correct handling/disposal of waste (oily rags, filters, packaging) and report any spill/leak immediately.Maintain assigned vehicle cleanliness and readiness; perform basic daily checks (tires, lights, fluids if applicable) and report defects.Operate company vehicles in full compliance with traffic rules and site speed limits; maintain safe driving behavior at all times (including outside the plant).Use fuel cards responsibly and report any suspected misuse/loss immediately.Operations and MaintenanceWind Turbine Maintenance (WTGExecute preventive and corrective maintenance on Vestas V90 3MW turbines in line with O&M procedures, ACWA OPERATIONS standards, and HSE requirements.Perform troubleshooting and diagnosis of turbine faults across mechanical, electrical, hydraulic, and basic control systems.Repair/replace defective components (as per competence level), including but not limited to: sensors, actuators, hydraulic components, yaw/pitch systems, brakes, coolingsystems, auxiliary power supply, and other turbine assemblies.Conduct tests and measurements to identify root causes and restore equipment to service (electrical tests, functional tests, basic calibrations, etc.).Use of check sheets + photo evidence for critical jobs (before/after, torque marking, damaged parts, oil leaks, corrosion, water ingress).Condition monitoring sampling support when assigned (oil samples, wear debris, grease sampling) with correct labeling/traceability.Standard as-found / as-left reporting in WO (measurements, alarms, cause hypothesis, parts used, next actions).Environmental controls: spill prevention basics, waste segregation, and immediate reporting of leaks (hydraulic oil, transformer area, etc.).Recognize turbine alarms/error codes and ensure accurate reporting and appropriate escalation when needed.Support wind turbine controller/automation basic maintenance and repair (within authorization and tool access).BoP Maintenance (Substation / MV Collection / Auxiliaries)Perform preventive and corrective maintenance for BoP equipment as assigned (MV/LV auxiliaries, earthing, lighting, small power, HVAC in control rooms, auxiliary transformers, etc.).Assist/participate in high-voltage maintenance activities as authorized (switching support, inspections, basic checks) and always under applicable rules and permits.Documentation & ReportingComplete all required paperwork and system entries accurately and on time: Work orders, checklists, reports, test results, PTWs, and maintenance logs.Document all maintenance and repair actions, including parts used, measurements taken, findings, and recommendations.Tools, Spares & Assets CareUse and maintain specialized tools and equipment properly (torque tools, test instruments, lifting accessories, hydraulic tools, etc.).Ensure proper care and correct usage of company tools, vehicles, and PPE.Support spare parts handling: identification, consumption recording, and feedback for replenishment (as per site process).Identifies required spare parts during execution, ensures correct parts consumption / reservation through the WO, and informs Technical Supervisor of any shortage or qualityissue observed.Supports traceability by documenting parts used, measurements taken, and findings in the WO/report and returning unused/defective parts as per site process.Lifting / Crane Support (When Applicable)Assist with heavy lift activities, including basic rigging support, exclusion zone setup, and acting as banksman/spotter when trained and authorized.Ensure lifting tools and accessories are inspected/certified before use.Continuous Improvement & Skills DevelopmentDemonstrate willingness to continuously build skills and progress toward advanced troubleshooting and repair capabilities.Participate in trainings, toolbox talks, and technical feedback loops to improve reliability and safety performance.Complete assigned TQP/online trainings, review relevant meeting records, and maintain readiness for operational and safety responsibilitiesIntegrated Management System AdherenceEnsure adherence to IMS procedures and contribute to achieving IMS objectives and targets at site level.Support IMS audits (internal/external) and ensure timely implementation and closure of assigned corrective actions.Support implementation of policies, procedures, and controls covering plant activities to meet procedural and legislative requirements.Develop, update, and maintain work instructions and maintenance procedures relevant to wind farm operations and maintenance.Relationship ManagementMaintain effective working relationships with internal and external stakeholders (Project Company, ONEE, OEM, contractors, service providers, local authorities, etc.) with high standards of business ethics.Ensure timely coordination and communication during critical site issues to support seamless plant operations.Comply with assigned work schedule, on-call duty, and approved leave plan; notify supervisor in advance in case of constraints and ensure proper handover and jobcontinuity </div></section><section>Desired Candidate ProfileMinimum Qualifications: DUT, BTS diploma/degree in electrical / Electromechanical Engineering or equivalentMinimum Experience:4-7 years experience in wind sector overseeing operation and maintenance.Or 2-3 years experience as a Wind Turbine Technician in Vestas V90 WTGs, including extensive experience in troubleshooting, up tower repairs, replacement of major components and operation (start/ stop/ reset) of WTGs.Technical Skills:Wind turbine troubleshooting + planned maintenance executionMV/HV substation & BoP coordination (switchgear, protection, transformers, MV cables)Basic ability to read technical documentation, electrical diagrams, and maintenance procedures.Strong reporting, RCA support, and action closure mindsetPlanning, prioritization, and performance-oriented deliverBehavioural competencies:Safety leadership & compliance mindsetAccountability and execution ownershipCommunication and collaborationProblem-solving and structured thinkingIntegrity, discipline, and resilience under pressure</section>

0 to 0 years Naukri Gulf

Molding Engineer

On-site - Morocco - Boulemane 6 July 2026

Engineering

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities: Degree: Bachelor's or Master's in Industrial Engineering, Advanced Diploma in Mechanical Manufacturing or Technical Engineering. Experience: Minimum 3-5 years of experience in a similar role, with specific expertise in molding (plastic injection, compression molding, extrusion molding, etc.). Technical Knowledge: Familiarity with CAD/CAM software for mold design (CATIA, SolidWorks, etc.). Knowledge of electricity, hydraulics, pneumatics, and automation. Materials Knowledge: Expertise in polymers, rubber, metals, or other materials used in molding. Knowledge of thermoplastic molds and injection processes. Analytical Skills: Ability to analyze complex technical problems and propose viable solutions. Production Methodologies: Knowledge of Lean Manufacturing practices, Six Sigma, and continuous improvement tools. Microsoft Office</div></section><section>Desired Candidate ProfileDegree: Bachelor's or Master's degree in Industrial Engineering, Advanced Diploma in Mechanical Manufacturing or Technical Engineering. Experience: Minimum 3-5 years of experience in a similar role, with specific expertise in molding (plastic injection, compression molding, extrusion molding, etc.). Technical Knowledge: Familiarity with CAD/CAM software for mold design (CATIA, SolidWorks, etc.). Knowledge of electricity, hydraulics, pneumatics, and automation. Materials Knowledge: Expertise in polymers, rubber, metals, or other materials used in molding. Knowledge of thermoplastic molds and injection molding processes. Analytical Skills: Ability to analyze complex technical problems and propose viable solutions. Production Methodologies: Knowledge of Lean Manufacturing practices, Six Sigma, and continuous improvement tools. Microsoft Office</section>

Contract 6 - 12 Years Naukri Gulf

Gas Pipeline Construction Supervisor

On-site - Morocco - Agadir 31 May 2026

Research & Development

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">We have the urgent requirement for the Construction Supervision Support Services - Gas PipelineJob Location - MoroccoJob duration: 9 months Required Position1 Sr. Construction Engineer2 HSE Supervisor3 QA/QC Supervisor4 Inspector for Major Equipment5 Civil Supervisor6 Mechanical Supervisor7 Welding & Coating Inspector </div></section><section>Desired Candidate ProfileCommon RequirementsAll proposed personnel shall meet the following minimum requirements:Relevant academic qualifications and technical certifications.Proven experience in Oil & Gas projects.Demonstrated exposure to Brownfield construction environments.Fluency in English is mandatory.French language proficiency is strongly preferred.<ol><li>Scope of Services</li></ol>The scope of services shall include, but not be limited to, the following activities:On-site supervision of construction activities performed by the contractor.Monitoring compliance with AFC (Approved for Construction) drawings, project specifications, and procedures.Assisting with inspection and testing activities.Monitoring HSE compliance on-site.Reporting on progress, issues encountered, and non-conformities.Coordination with the Client project team, construction contractor, and client representatives.Review of Method Statements and Inspection and Test Plans (ITPs)</section>

0 to 0 years Bayt

Senior General Installation Engineer

On-site - Morocco 9 July 2026

Construction & Real Estate

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Company culture : Capgemini Engineering is characterized by a strong collaborative culture, placing people, trust and teamwork at the core of its operations. A close management approach supports guidance, empowerment and talent development within a caring environment. This dynamic is reinforced by a significant innovation dimension, encouraging creativity, initiative and experimentation to deliver high-value solutions. It is also supported by a structured organizational foundation ensuring rigor and reliability, while a more moderate competitive component sustains a balanced performance mindset. Job : Your mission: Within our project teams, you will support the building manager in the production and monitoring of general installation studies by bringing your technical expertise and your global vision of industrial projects. As a General Installation Engineer, you will be responsible for: <ul><li>Studying the layout of different equipment and materials on the 3D model.</li><li>Receiving input data related to the general installation of the building, analyzing them and verifying their technical consistency.</li><li>Monitoring modifications requested by different engineering disciplines.</li><li>Verifying the consistency between detailed mechanical diagrams and the 3D model by coordinating the activities of draftsmen and designers.</li><li>Leading and conducting general installation reviews with the various project stakeholders.</li><li>Identifying blocking points and proposing associated action plans.</li><li>Developing and maintaining the status of the model by integrating the latest available input data.</li><li>Participating in multidisciplinary coordination to ensure optimal integration of equipment and networks while respecting technical, safety, and operational requirements.</li></ul> Required profile : Graduated from an engineering school or holder of a Bac+5 in Mechanical Engineering, General Installation, Civil Engineering, or equivalent. You have significant experience in general installation studies on complex industrial projects. You have a technical English level of B2 minimum, allowing you to interpret technical documentation and communicate in an international environment. You are proficient in reading plans, technical diagrams, and 3D models. You have strong skills in technical coordination and interface management between disciplines. You are recognized for your rigor, your analytical skills, your organizational skills, and your ability to work in a team. Experience in one of the following sectors is highly appreciated: <ul><li>Thermal power plants;</li><li>Electricity production;</li><li>Industrial turbomachinery (gas turbines, steam turbines);</li><li>Heavy industry (cement, steel, chemical);</li><li>Water desalination;</li><li>Oil & Gas</li></ul> Some reasons to join us: • Quality of work life: Possibility of teleworking in Morocco and internationally and autonomy in organizing your daily life, hybrid missions according to your preferences. • Continuous learning: access to training and certifications dedicated to your technology, personalized support, and a structured integration process. • Varied and high-impact projects: work with major clients in diverse sectors with stimulating business and technological challenges. </div>

0 to 0 years Naukri Gulf

Lawyer

On-site - Morocco - Casablanca 6 July 2026

Legal

<section>Job DescriptionRoles & Responsibilities<div class="paragraph"> Context & Environment <div> <div> <div> </div> <ul> <li>A highly competitive environment requiring a rapid and precise response,</li> <li>A multitude of internal and external stakeholders,</li> <li>A young and newly reconstituted team.</li> </ul> <div> </div> </div> </div> <div> <div> <div> Activities </div> </div> <div> <div> <div> <div> Business Law: <ul> <li>Review, negotiate and draft all contractual documentation relating to the Company's activity, and implement contract templates.</li> <li>To review and provide legal opinions and consultations on all legal issues encountered by the Company,</li> <li>Register the company's service stations with the competent commercial courts,</li> </ul> Real estate : <ul> <li>Monitoring, updating and remediation of the company's land assets,</li> <li>Assistance to operational staff for field assessments,</li> <li>Monitoring of land subdivision projects,</li> <li>Lease monitoring.</li> </ul> Others : <ul> <li>Managing business litigation in collaboration with law firms,</li> <li>Ensure regulatory monitoring and follow-up of authorizations.</li> </ul> </div> </div> </div> </div> </div> <div> <div> <div> Candidate Profile </div> </div> <div> <div> <div> </div> <div> <ul> <li>Advanced training in business law / private law,</li> <li>Five years' experience in a corporate legal role within a law firm or large organization,</li> <li>Good knowledge of Moroccan regulations and case law,</li> <li>Good interpersonal skills</li> <li>Perfectly bilingual in Arabic and French, good level of English.</li> <li>Autonomy and rigor,</li> <li>Sense of analysis and synthesis,</li> <li>Qualit sr actionnelles,</li> <li>A sense of teamwork,</li> <li>Meaning of ethics.</li> </ul> </div> </div> </div> </div> <div> <div> <div> </div></div><div><div> </div></div></div></div></section>

0 to 0 years Bayt

Project Leader

On-site - Morocco 22 July 2026

Other

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Who We Are Boston Consulting Group partners with leaders in business and society to tackle their most important challenges and capture their greatest opportunities. BCG was the pioneer in business strategy when it was founded in 1963. Today, we help clients with total transformation-inspiring complex change, enabling organizations to grow, building competitive advantage, and driving bottom-line impact. To succeed, organizations must blend digital and human capabilities. Our diverse, global teams bring deep industry and functional expertise and a range of perspectives to spark change. BCG delivers solutions through leading-edge management consulting along with technology and design, corporate and digital ventures—and business purpose. We work in a uniquely collaborative model across the firm and throughout all levels of the client organization, generating results that allow our clients to thrive.  What You'll Do As a Project Leader at BCG’s Casablanca office, you will lead consulting teams and work closely with senior executives cross-sector, for example, mining, financial services, government or public sector or industrial goods to address their most critical strategic and operational challenges. You will play a key role in structuring complex problems, developing recommendations, and ensuring projects deliver meaningful and sustainable impact. You will collaborate with colleagues and industry experts across Casablanca and BCG’s global network to help clients navigate disruption, accelerate digital transformation, strengthen risk and regulatory capabilities, and unlock new growth opportunities. Examples of engagements may include: <ul><li>Develop a growth strategy for the retail banking business of an African financial group</li><li>Develop a Decarbonization Roadmap for Global Fertilizer Player </li><li>Building comprehensive Target Operating Model for Crisis Management in Mining </li><li>Physical Climate Risk Assessment for an Oil and Gas Player </li></ul> On a day-to-day basis, you will: <ul><li>Lead project teams to analyse complex challenges and deliver strategic recommendations across sectors</li><li>Translate analytical insights into clear, actionable strategies for senior client stakeholders</li><li>Manage project execution, ensuring high-quality delivery, strong collaboration, and timely outcomes</li><li>Build trusted relationships with client leaders and facilitate productive discussions and decision-making</li><li>Coach and develop junior consultants, fostering a collaborative and high-performing team environment</li><li>Contribute to knowledge development and thought leadership within BCG’s practices</li><li>Support business development activities, including proposal preparation and client engagement</li></ul> What You'll Bring <ul><li>7 to 12 years of relevant experience in top-tier consulting, or a related industry with demonstrated consulting experience</li><li>Deep expertise in one or more sectors (for example, mining, industrial goods, automotive, energy, government/ public, banking/ financial services, digital transformations)</li><li>Demonstrated expertise in project management and leadership to provide proficiency in prioritizing and balancing multiple project demands</li><li>Excellent analytical, and strategic thinking abilities to develop transformative solutions</li><li>Exceptional stakeholder management and communication skills to engage and align cross functional teams</li><li>Adept at relationship building and client management across various levels.</li><li>Commitment to inclusivity, developing others and creating an environment of mutual trust and respect</li></ul> Who You'll Work With BCG aims to be the consultant of choice for leaders in the consulting industry. The Casablanca office operates at the intersection of some of the region's most complex strategic challenges- from large-scale industrial transformation to financial sector evolution and the energy transition. You will work alongside senior BCG leaders and collaborate across offices to bring the best of the firm to every engagement. Boston Consulting Group is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, age, religion, sex, sexual orientation, gender identity / expression, national origin, disability, protected veteran status, or any other characteristic protected under national, provincial, or local law, where applicable, and those with criminal histories will be considered in a manner consistent with applicable state and local laws. BCG is an E - Verify Employer. Click here for more information on E-Verify. </div>

0 to 0 years Bayt

Process Technician

On-site - Morocco 10 July 2026

Information Technology

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Company culture : Cosumar is characterized by a corporate culture centered on collaboration, where human relationships, teamwork and employee support play an important role. This collaborative approach is reinforced by a strong organizational dimension, ensuring rigor, efficiency and process reliability. The company also values performance and goal achievement, while maintaining openness to innovation and continuous improvement. This balance fosters a structured, people-oriented and progress-driven work environment. Job : Join a dynamic company in the Agri-food sector as a PROCESS TECHNICIAN at one of our sites located in the Loukkos region. This is a unique opportunity to actively contribute to production processes in a stimulating environment. Your role will be essential in optimizing manufacturing processes, ensuring product compliance, and adhering to safety standards. The goal is to guarantee efficient, high-quality production. Your main tasks will include: Ensuring maintenance of technological equipment: • Prepare the maintenance program considering the pre-established maintenance plan and analysis of past breakdowns during the campaign • Open, dismantle, and diagnose equipment and establish the list of spare parts needed for interventions • Check the availability of spare parts in coordination with the storekeeper and act accordingly • Ensure the maintenance program is carried out within the deadlines • Propose improvement actions to the line manager and implement validated actions • Support external service providers in carrying out outsourced maintenance work • Prepare the weekly progress report of the work and send it to the line manager Perform and/or participate in tests: • Participate in mechanical tests of equipment and ensure work is done to remove reservations made by the testing committee • Perform hot tests of the station, check interlocks, and correct any malfunctions Campaign: Configure the station's equipment according to operational requirements and management instructions • Prepare and commission the station's equipment in coordination with the power plant and the distribution station Operate the drying and pelletizing station: • Prepare your workstation and familiarize yourself with operating and maintenance instructions • Monitor the process parameters and act appropriately • Consult laboratory analysis results and act accordingly • Start and monitor the cleaning operation of the relevant machines. • Complete tracking forms • Inform management of any significant events related to the station's operation • At the end of the campaign, clean and preserve the equipment Monitor the proper functioning of equipment: Perform rounds to check the proper functioning of equipment and notify the relevant maintenance department in case of malfunction • Monitor the smooth running of the packaging operation • Perform maintenance tasks that are your responsibility (lubrication, oil level, etc.) Prevent HSE risks in your activities: • Participate in identifying risks in your work area • Observe prescribed precautions and protections • Apply standards in every action Participate in continuous improvement projects: • Ensure optimization and achievement of energy consumption objectives • Conduct briefing and debriefing meetings with the line manager • Propose improvement actions to the line manager for validation and implement validated actions Required profile : You have a Bac+2/3 level education in process engineering, electromechanics, or equivalent. Internship experience in a similar role is required, ideally in the agri-food sector or heavy industry. If you see yourself in this profile and are ready to take on this challenge, do not hesitate to apply quickly using the button "Send my CV to the recruiter" below. </div>

0 to 0 years Bayt

Manufacturing Technician

On-site - Morocco 1 July 2026

Engineering

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Company culture : Cosumar is characterized by a corporate culture centered on collaboration, where human relationships, teamwork and employee support play an important role. This collaborative approach is reinforced by a strong organizational dimension, ensuring rigor, efficiency and process reliability. The company also values performance and goal achievement, while maintaining openness to innovation and continuous improvement. This balance fosters a structured, people-oriented and progress-driven work environment. Job : Join a dynamic company in the Agri-food sector as a MANUFACTURING TECHNICIAN at one of our sites located in the Gharb region. This is a unique opportunity to actively contribute to production processes in a stimulating environment. Your role will be essential in optimizing manufacturing processes, ensuring product compliance, and adhering to safety standards. The goal is to guarantee efficient, high-quality production. Your main tasks will include: <ul><li> Ensure maintenance of technological equipment: • Prepare the maintenance program considering the pre-established maintenance plan and the analysis of past breakdowns during the campaign • Proceed with the opening, dismantling, and diagnosis of equipment and establish the list of spare parts needed for interventions • Check the availability of spare parts in coordination with the storekeeper and act accordingly • Ensure the maintenance program is completed within the set deadlines • Propose improvement actions to the line manager and implement validated actions • Support external service providers in carrying out outsourced maintenance work • Prepare the weekly progress report of work and send it to the line manager Perform and/or participate in tests: • Participate in mechanical tests of equipment and ensure work is done to clear issues identified by the testing committee • Perform hot tests of the station, check interlocks, and fix any malfunctions Campaign: Configure station equipment according to operating requirements and management instructions • Prepare and commission station equipment in coordination with the power plant and the distribution station Operate the drying and pelletizing station: • Prepare your workstation and familiarize yourself with operating and maintenance instructions • Monitor the evolution of process operating parameters and act appropriately • Consult laboratory analysis results and act accordingly • Start and monitor the cleaning operation of the relevant machines. • Complete tracking forms • Inform management of any significant events related to the station's operation • At the end of the campaign, clean and preserve the equipment Monitor the proper functioning of equipment:</li><li>Perform rounds to check the proper functioning of equipment and notify the relevant maintenance department in case of malfunction • Monitor the smooth running of the packaging operation • Perform maintenance tasks that fall under your responsibility (greasing, oil level, etc.) Prevent HSE risks in carrying out your activities: • Participate in identifying risks in your work area • Observe prescribed precautions and protections • Apply standards in every action Participate in continuous improvement projects: • Ensure optimization and achievement of energy consumption targets • Conduct briefing and debriefing meetings with the line manager • Propose improvement actions to the line manager for validation and implement the validated actions </li></ul> Required profile : You have a Bac+2/3 level education (equivalent to an Associate's or Bachelor's degree) in process engineering, electromechanics, or equivalent. Experience as an intern in a similar role is required, ideally in the agri-food sector or heavy industry. If you see yourself in this profile and are ready to take on this challenge, do not hesitate to apply quickly using the "Send my CV to the recruiter" button below. </div>

0 to 0 years Naukri Gulf

Production Assistant

On-site - Morocco - Boulemane 6 July 2026

Logistics, Supply Chain & Procurement

<section>Job DescriptionRoles & Responsibilities<div class="paragraph"><div><div> As a production assistant, your responsibilities will be as follows*: <ul> <li>Preparation of manufacturing files (work orders, labels, PLP, etc.)</li> <li>Archive and classify reusable documents</li> <li>Participate in the preparation of weekly/monthly production reports,</li> <li>Create new weekly production tracking files,</li> <li>Manage the supply of office and workshop supplies</li> <li>Perform photocopying, document lamination, label cutting, etc., necessary for the smooth operation of the production workshop.</li> <li>To carry out all tasks within the scope of their duties or as requested by their supervisor.</li> </ul> * Non-exhaustive list Skills and knowledge required <ul> <li>You have a Bac+2 qualification and some initial experience in a similar position;</li> <li>You are proficient with computer tools and the Office suite;</li> <li>You are comfortable communicating in French, both in writing and orally.</li> </ul> What we offer you: <ul> <li>You will be working in a dynamic and growing environment.</li> <li>You will benefit from the agility and flexibility of an SME combined with the solidity and resources of an international group that has existed for 170 years.</li> <li>You will benefit from a personalized integration program upon taking up your position, regular training within a group where career development prospects are rich and diverse.</li> <li>We aim for carbon neutrality by 2050 for all our activities.</li> <li>We invest 5% of our turnover every year for the past 20 years in innovation for sustainable development.</li> </ul></div></div><div> </div></div></section>

0 to 0 years Bayt

Manufacturing Technician

On-site - Morocco 10 July 2026

Construction & Real Estate

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> Company culture : Cosumar is characterized by a corporate culture centered on collaboration, where human relationships, teamwork and employee support play an important role. This collaborative approach is reinforced by a strong organizational dimension, ensuring rigor, efficiency and process reliability. The company also values performance and goal achievement, while maintaining openness to innovation and continuous improvement. This balance fosters a structured, people-oriented and progress-driven work environment. Job : Join a dynamic company in the Agri-food sector as a MANUFACTURING TECHNICIAN at one of our sites located in the DOUKKALA region. This is a unique opportunity to actively contribute to production processes in a stimulating environment. Your main tasks will include: Ensure maintenance of technological equipment: • Prepare the maintenance program taking into account the pre-established maintenance plan and the analysis of the breakdown history during the campaign • Proceed with the opening, dismantling, and diagnosis of equipment and establish the list of spare parts (PDR) needed for interventions • Check the availability of spare parts in coordination with the storekeeper and act accordingly • Ensure the maintenance program is carried out within the deadlines • Propose improvement actions to the line manager and implement validated actions • Support service providers in carrying out outsourced maintenance work • Prepare the weekly progress report of the work and send it to the line manager • Participate in mechanical tests of equipment and ensure the work is carried out to remove reservations made by the testing commission • Perform hot tests of the station, check interlocks, and remedy any potential malfunctions Campaign: Configure the station's equipment according to operating requirements and management instructions • Prepare and commission the station's equipment in coordination with the power plant and the distribution station Operate the drying and pelletizing station: • Prepare your workstation and familiarize yourself with operating and maintenance instructions • Monitor the progress of the process parameters and act appropriately • Consult laboratory analysis results and act accordingly • Start and monitor the cleaning operation of the relevant machines. • Fill out tracking sheets • Inform management of any significant event related to the station's operation • At the end of the campaign, clean and maintain the equipment Monitor the proper functioning of equipment: Perform rounds to check the proper functioning of equipment and notify the relevant maintenance department in case of malfunction • Monitor the proper progress of the packaging operation • Perform maintenance tasks within your responsibility (greasing, oil level, etc.) Prevent HSE risks in your activities: • Participate in identifying risks in your work area • Observe prescribed precautions and protections • Apply standards in every action Participate in continuous improvement projects: • Ensure the optimization and achievement of energy consumption objectives • Conduct briefing and debriefing meetings with the line manager • Propose improvement actions to the line manager for validation and implement validated actions Required profile : You have a Bac+2/3 level education in process engineering, electromechanics, or equivalent. Experience as an intern in a similar role is required, ideally in the agri-food sector or heavy industry. If you see yourself in this profile and are ready to take on this challenge, do not hesitate to apply quickly using the button "Send my CV to the recruiter" below. </div>

0 to 0 years Naukri Gulf

Production Supervisor

On-site - Morocco - Boulemane 6 July 2026

Logistics, Supply Chain & Procurement

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Ensure production in compliance with the procedures and instructions provided at the workstation; Ensure compliance with the schedule established by his manager; Be responsible for the production program of his team; Guarantee the quality of manufactured products in compliance with the control process; Monitor the recording of production, waste, and breakdowns in EAM in real time; Inform his hierarchical manager in case of production problems; Actively participate in the site's improvement plan actions; Actively participate in the safety and performance suggestion system; Organize work distribution within his team; Ensure team changeovers (cleanliness of the area, handover of necessary instructions to the relief team); Manage his team's movements within the framework of internal rules; Ensure the integration and training of new hires at their workstation; Participate in the analysis of quality problems and corrective actions; Actively participate in the site's improvement plan actions; Stop production in case of Quality, safety, or environmental problems and implement necessary actions; Establish the weekly assignment; Guarantee the continuous improvement process in his sector; Ensure compliance with manufacturing processes while optimizing consumption and respecting the FIFO of products and materials; Enforce working hours, instructions, discipline, and procedures; Ensure compliance with hygiene, quality, environmental, safety rules, and factory cleanliness; Update documents related to Training (Schedule and versatility grid); Ensure coordination between team leaders; Ensure team management; Prepare internal and external audits; Ensure follow-up of new recruit training and job changes; Establish and display production indicators.</div></section>

0 to 0 years Naukri Gulf

IT Technician

On-site - Morocco - Boulemane 6 July 2026

Information Technology

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Job Description: Local + Permanent Contract Your Role: The IT Technician is responsible for installing and connecting the company's IT and telephone equipment. In addition to installation (cabling, connecting devices to each other and to external networks, configuring network equipment), the network and telecom technician maintains the system, ensures its proper functioning, advises users, performs regular tests, anticipates potential incidents, and intervenes in case of breakdowns. Training users on basic IT tools such as GLPI is also required. As an IT Technician, your responsibilities will include the following*: Managing work tools: Office 365, GLPI, user account management, and antivirus software; Replacing and managing consumables; Network maintenance and troubleshooting as needed; Maintenance and deployment of workstations; Monitoring external service providers as needed (preventive/corrective maintenance); Managing the IT infrastructure (PCs, printers, video surveillance) and software; Providing technical support for workstations at different sites and/or remotely; Performing all tasks within the scope of your duties or as requested by your supervisor. *This list is not exhaustive. Required Skills and Knowledge: A Bachelor's degree (or equivalent) specializing in Administration/IT is required. 1 to 3 years of experience in a similar role is required; experience in industry is preferred. Proficiency in various IT tools and software is essential. Having knowledge of networking (TCP/IP, OSI) Having good knowledge of Microsoft technologies (Windows server, workstation, Active Directory) Your interpersonal skills, your curiosity, but also your ability to be proactive and to be oriented towards innovation will allow you to carry out your missions well and to thrive in this position.</div></section><section>Desired Candidate Profile<ul><li>Be a graduate with a Bac+3 specialisation in administration / IT.</li><li>1-3 years of experience in a similar position; industry experience will be required.</li><li>Mastering computer tools and various software.</li><li>Knowledge of networking (TCP/IP, OSI)</li><li>Have a good knowledge of Microsoft technologies (Windows server, workstation, Active Directory)</li><li>Your interpersonal skills, your curiosity, but also your ability to be proactive and to be oriented towards innovation will allow you to carry out your missions successfully and to thrive in this position.</li></ul></section>

0 to 0 years Bayt

Business Development Manager

On-site - Morocco 28 July 2026

Sales

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> The position is available in: Nigeria; Morocco; Ghana; Ivory Coast; Senegal; Angola; DRC; South Africa; Kenya; Tanzania; Uganda; Algeria; Cameroon; Egypt You are invited to apply if you're a citizen of the above mentioned countries. The successful candidate will be responsible for developing sales within the assigned territory, identifying new customers, managing distributors, and growing profitable B2B business with manufacturers and industrial end users. This is a field-based commercial role requiring a self-driven individual capable of opening new markets and representing the company professionally. Key Responsibilities • Develop new customers and expand existing accounts. • Generate sales across industrial chemical market segments. • Manage distributors, agents and key accounts. • Prepare quotations, negotiate commercial terms and close business. • Develop annual territory and customer plans. • Monitor competitors, pricing and market trends. • Coordinate with logistics, customer service and technical teams. • Achieve agreed sales, margin and collection targets. • Travel extensively within the assigned territory. Preferred Industry Experience • Industrial Chemicals • Petrochemicals • Solvents • Lubricants & Base Oils • Paints & Coatings • Resins & Adhesives • PVC & Polymer Raw Materials • Oilfield Chemicals • Water Treatment Chemicals • Specialty Chemicals RequirementsQualifications • Bachelor's Degree in Chemical Engineering, Chemistry, Petrochemical Engineering, Industrial Engineering, Business Administration, International Business, Marketing or a related discipline. • An MBA in Sales, Marketing or International Business will be an added advantage. • Professional training or certifications in International Sales, Export Management, Key Account Management or Business Development are preferred. • Strong technical understanding of industrial chemicals, petrochemicals, lubricants, base oils, solvents or related products is highly desirable. Candidate Requirements • Minimum 5 years of B2B sales experience. • Existing customer relationships within the assigned country or region. • Experience selling to manufacturers, distributors and industrial end users. • Strong negotiation and presentation skills. • Commercial understanding of industrial chemical applications. • Ability to work independently with minimal supervision. • Willingness to travel extensively. • Valid driving licence (where applicable). • English required; French and/or Arabic is an advantage depending on the region. Business Equipment (Mandatory) As this is a hybrid role, candidates must have: • Personal laptop suitable for business use. • Own vehicle for customer visits and business travel. • Business mobile phone with reliable connectivity. • Stable high-speed internet connection and a professional home office setup. Kindly consider your application unsuccessful should you not be contacted within 7 working days </div>

0 to 0 years Naukri Gulf

FAI Technician

On-site - Morocco - Boulemane 6 July 2026

Research & Development

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities Live an extraordinary and unique adventure within a large industrial group The agility and autonomy of an SME Contract Type: Local Permanent contract Your role: The FAI Technician's mission is to ensure that products manufactured by our production teams meet the specifications and quality standards required by the client before launching mass production. As an FAI Technician, your responsibilities will be as follows*: Prepare in advance all necessary documents, including plans and product specifications; Analyze work documents in advance against client requirements; Document the results of the inspection and the raw materials used and processes applied; Analyze the data collected during the analysis to identify any non-conformities or manufacturing problems compared to client requirements and report them to the teams for correction; Write a First Article Inspection Report (FAIR) detailing the results of the first manufactured part; Communicate inspection results to stakeholders, including clients; Follow up on FAIRs and the planning for completing dossiers; Communicate with the client in case of changes and report to the production and ME teams.</div></section><section>Desired Candidate ProfileSkills and knowledge required: Hold a Bac+2 level education or higher in Quality; Have significant experience in quality, methods, or production; Have 3 years of experience in the aeronautics sector; Mastery of French and English, both written and spoken; Mastery of office tools (Office); Mastery of reading plans; Ability to analyze client specifications; Knowledge of EN9102 Your interpersonal skills, your curiosity, as well as your ability to be proactive and innovation-oriented will allow you to successfully carry out your missions and thrive in this role. You will evolve in a dynamic and growing environment. You will benefit from the agility and flexibility of an SME combined with the solidity and resources of an international group that has existed for 170 years. You will benefit from a personalized integration program for your onboarding, regular training within a group where career development prospects are rich and diverse. We are committed to an environmental and societal policy (CSR) regarding Biodiversity, Diversity & Inclusion, Parenthood, Ethics, and Skills Development. We aim for carbon neutrality by 2050 for all our activities. We invest 5% of our turnover, every year for the past 20 years, in innovation for sustainable development.</section>

0 to 0 years Naukri Gulf

Industrial Maintenance and New Works Coordinator

On-site - Morocco - Boulemane 6 July 2026

Engineering

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities Live an extraordinary and unique adventure within a large industrial group, with the agility and autonomy of an SME.Type of Contract: Local Permanent ContractYour roleThe industrial maintenance and new works coordinator helps optimize the maintenance of production facilities and ensures that production is not stopped. He/she is responsible for piloting investment projects and new works, while respecting HSE standards. He/she also manages and coordinates all phases of construction projects, from assembly and design to final delivery.As an Industrial Maintenance and New Works Coordinator, your responsibilities will be:<ul><li>Coordinate construction and investment projects;</li><li>Ensure the follow-up of completion schedules;</li><li>Define the costs and deadlines associated with each project;</li><li>Ensure compliance with current quality standards;</li><li>Guarantee the proper execution of works and the integration of projects within the living environment and compliance with construction rules;</li><li>Identify technical solutions for improving installations and equipment (quality, capability, cycles, safety, etc.);</li><li>Monitor the compliance of interventions and the operation of materials, installations, and equipment (receptions, tests, trials, adjustments, etc.);</li><li>Industrial works carried out by his/her personnel or by subcontracting companies;</li><li>The implementation of new industrial means such as machines, air-conditioned rooms, etc., with the management of subcontractor works (establishment of specifications, quote consultation, negotiation, order placement, pre-installation follow-up, site management and external services, works reception);</li><li>Management of maintenance activity monitoring indicators (dashboards, reporting, energy consumption);</li><li>Ensure all missions within the scope of his/her functions or at the request of the hierarchical manager;</li><li>Manage maintenance activity monitoring indicators (dashboards, reporting, energy consumption).</li></ul></div></section><section>Desired Candidate ProfileRequired Skills and Knowledge:<ul><li>Hold a Bac +3 or Bac+5 degree in mechanical/industrial maintenance;</li><li>Have 2 to 3 years of experience in a similar position;</li><li>Proficiency in written and spoken French;</li><li>Proficiency in office tools essential for his/her activity (spreadsheet, database, accounting software, etc.) and the company's ERP;</li><li>Expertise in mechanical, electrical, automation, and pneumatic fields;</li><li>Ability to work in a team and communicate effectively;</li><li>Driver's license mandatory.</li></ul>Your interpersonal skills, curiosity, and ability to be proactive and innovative will enable you to successfully carry out your missions and thrive in this role.</section>

0 to 0 years Naukri Gulf

Industrial Maintenance Technician

On-site - Morocco - Boulemane 6 July 2026

Engineering

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities Live an extraordinary and unique adventure within a large industrial group, the agility and autonomy of an SME. Type of Contract: Local Permanent Contract. Your role The Industrial Maintenance & New Works Technician maintains, repairs, revises, and modifies electronic and electrical equipment. He must demonstrate good technical knowledge but also be a good listener to understand the technical constraints encountered by his interlocutor. As an Industrial Maintenance & New Works Technician, your responsibilities will be as follows*:Ensure preventive and corrective maintenance of industrial equipment; Reduce machine downtime; Fill in intervention reports and ensure equipment monitoring; Guarantee the reliability and safety of equipment in compliance with safety, quality, and environmental rules; Contribute to the optimization of maintenance costs and continuous improvement of installations; Carry out preventive and corrective maintenance interventions on industrial equipment; Diagnose breakdowns and propose appropriate solutions; Perform adjustments, repairs, and replacements of defective parts; Participate in the installation and commissioning of new machines; Supervise on-site interveners; Check the proper functioning of machines after intervention; Comply with safety standards and internal procedures; Contribute to the continuous improvement of maintenance processes; Ensure the tidiness and cleanliness of the maintenance workshop.</div></section><section>Desired Candidate Profile<ul><li>Be from a Bac+2 level of education or higher;</li><li>Having 5 years of experience in a similar position;</li><li>Mastery of the French language, both written and spoken;</li><li>Mastery of diagnostic and measurement tools;</li><li>Technical versatility (electricity, mechanics, hydraulics, and automation);</li><li>Ability to read and interpret electrical and mechanical diagrams;</li><li>Ability to work in a team and communicate effectively;</li><li>Driving license required</li></ul>Your interpersonal skills, your curiosity, as well as your ability to be proactive and oriented towards innovation will allow you to successfully carry out your missions and thrive in this position.</section>

0 to 0 years Naukri Gulf

Industrial Maintenance Technician

On-site - Morocco - Boulemane 6 July 2026

Logistics, Supply Chain & Procurement

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities Live an extraordinary and unique adventure within a large industrial group. The agility and autonomy of an SME. Contract Type: Local Permanent Contract. Your role: The Industrial Maintenance & New Works Technician maintains, repairs, revises, and modifies electronic and electrical equipment. He must have good technical knowledge but also be a good listener to understand the technical constraints encountered by his interlocutor. As an Industrial Maintenance & New Works Technician, your responsibilities will be the following*: Ensure preventive and corrective maintenance of industrial equipment; Reduce machine downtime; Fill in intervention reports and ensure equipment monitoring; Guarantee the reliability and safety of equipment by respecting safety, quality, and environmental rules; Contribute to the optimization of maintenance costs and continuous improvement of installations; Carry out preventive and corrective maintenance interventions on industrial equipment; Diagnose breakdowns and propose appropriate solutions; Perform adjustments, repairs, and replacements of defective parts; Participate in the installation and commissioning of new machines; Supervise on-site interveners; Check the proper functioning of machines after intervention; Comply with safety standards and internal procedures; Contribute to the continuous improvement of maintenance processes; Ensure the tidiness and cleanliness of the maintenance workshop.</div></section><section>Desired Candidate ProfileRequired skills and knowledge: Must have a Bac+2 education or higher; Have 5 years of experience in a similar position; Mastery of the French language, both written and oral; Mastery of diagnostic and measurement tools; Possess technical versatility (electricity, mechanics, hydraulics, and automation); Ability to read and interpret electrical and mechanical diagrams; Ability to work in a team and communicate effectively; Driving license required. Your interpersonal skills, your curiosity, as well as your ability to be proactive and innovation-oriented will allow you to successfully carry out your missions and thrive in this position.</section>

0 to 0 years Naukri Gulf

Quality Engineer

On-site - Morocco - Boulemane 6 July 2026

Research & Development

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities Live an extraordinary and unique adventure within a large industrial group the agility and autonomy of an SME Type of Contract: Local CDI Your role The quality engineer is the guarantor of the company's product quality and monitors them from design to industrialization, constantly ensuring compliance with procedures. Always mindful of respecting costs and deadlines, they implement indicators, quality tools, and control procedures valid during manufacturing. They can thus identify dysfunctions or detect non-compliance with standards, carry out audits, and participate in problem-solving. As a Quality Engineer, your responsibilities will be as follows*: Provide technical and methodological assistance for training production personnel, technical personnel, and other personnel in the production of subcontracted composite aeronautical parts HCIM (and updates). Manage the maintenance of qualification and multi-skill authorization matrices for maintenance personnel. Manage current quality documentation in compliance with the quality rules of the aeronautical standard EN 9100. Report to technical departments the discrepancies identified between quality requirements and technical documentation. Prepare and participate in audits (customer and regulatory). Ensure customer acceptance, FAI. Participate in quality investigations, corrective and preventive actions. Supervise control activities and manage authorized control personnel. Draft (if applicable) and process non-conformity reports (PVNC) and customer complaints. Participate in the management and animation of continuous improvement initiatives related to various points concerning: Manufacturing non-conformity (part NC, compliance with various procedures and instructions, etc.) Manufacturing improvement (various optimizations, etc.) Organize general monitoring of non-conformities and establish summaries of results relating to optimization and action follow-up work. Ensure responsibilities related to production: Ensure compliance with access and product preservation rules. Ensure compliance with hygiene and safety rules. Other as requested. Organize and monitor the work of trainers concerning: Integration of new operators. Monitoring internal non-conformities. Monitoring customer non-conformities (internal and external). Organize follow-up meetings, establish, prioritize, and close actions to be carried out. Ensure all missions within the scope of their responsibilities or as requested by the hierarchical manager.</div></section><section>Desired Candidate Profile<ul><li>Be a graduate of Bac+5, engineer or equivalent;</li><li>Good technical quality training;</li><li>Have at least 3 years of experience in an industrial environment;</li><li>Proficiency in Office tools;</li><li>Good proficiency in problem-solving methodology tools;</li><li>Sense of commitment and responsibility;</li><li>Strong involvement and desire to learn;</li><li>Your interpersonal skills, your curiosity, but also your ability to be proactive and innovation-oriented will enable you to successfully carry out your missions and thrive in this position.</li></ul></section>

0 to 0 years Naukri Gulf

Buyer

On-site - Morocco - Boulemane 6 July 2026

Logistics, Supply Chain & Procurement

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Activities Description Experience an extraordinary and unique adventure within a large industrial group, with the agility and autonomy of an SME. Contract type: Local; Fixed-term contract. Your role: The lead buyer for goods and services has the primary mission of managing the company's purchases. They choose products and suppliers, and negotiate the best purchasing conditions (price, quality, delivery, etc.). As the Lead Buyer for Goods and Services, your responsibilities will be as follows*: Manage the purchasing process in accordance with procedures and instructions; Support the Goods and Services Purchasing team on a daily basis; Regularly report to management on the progress of predefined action plans via monthly reports; Obtain approval from management for: draft contracts and tender documents; Collect and allocate the needs expressed by departments for the goods and services purchasing categories; Assist other departments in clearly defining their needs; Ensure the receipt of goods and services by customer departments, according to procedures and internal controls; Propose, after approval by management, ways to optimize processes or IT tools identified within the scope of your role; Manage tenders/consult suppliers; Participate in the selection of successful bidders; Manage the contracting process/contract with successful bidders; Ensure compliance with obligations of each party. Contribute to resolving certain delicate or contentious situations. Ensure all missions within the scope of your duties or as requested by your supervisor. Participate in project meetings and QRQC. Develop KPIs and monitor action plans. *Non-exhaustive list. Required skills and knowledge: Hold a Master's degree (Bac+5) from an engineering or business school. Have 1-3 years of experience in a similar position; experience in aeronautics will be required. Proficiency in ERP systems, SAP, and Office tools. Your interpersonal skills, curiosity, and ability to be proactive and innovative will allow you to successfully carry out your missions and thrive in this position. You will work in a dynamic and growing environment. You will benefit from the agility and flexibility of an SME combined with the stability and resources of an international group with 170 years of experience. You will benefit from a personalized onboarding program upon starting your position, as well as regular training within a group where career development opportunities are plentiful and diverse. We are committed to an environmental and social (CSR) policy focusing on Biodiversity, Diversity & Inclusion, Parenthood, Ethics, and Skills Development. We aim for carbon neutrality by 2050 for all our activities.We invest 5% of our revenue every year for the past 20 years in innovation for sustainable development. Additional Information: TotalEnergies values diversity, promotes individual growth, and offers equal opportunity careers.</div></section><section>Desired Candidate ProfileCandidates should hold a Master's degree (Bac+5) from an engineering or business school and have 1-3 years of experience in a similar role; experience in the aeronautics sector is required. Proficiency in ERP systems, SAP, and Microsoft Office tools is essential. Your interpersonal skills, curiosity, proactive approach, and innovative mindset will enable you to successfully fulfill your responsibilities and thrive in this position.</section>

0 to 0 years Naukri Gulf

Controller

On-site - Morocco - Boulemane 6 July 2026

Accounting, Finance & Banking

<section>Job DescriptionRoles & Responsibilities<div class="paragraph">Reporting to the Finance & Management Control Manager, the Management Controller conducts economic and financial analyses through group reporting, ensuring deadlines are met. The results of this work enable the operational and strategic management of the company. As Management Controller, your responsibilities will be as follows*: establish the master plan for budgets and long-term plans (forecasts in terms of revenue, production costs, fixed costs, and fixed assets); ensure the distribution and analysis of flash reports (monthly closing + 6-month forecasts), explaining variations to Management; prepare and distribute the various reports requested by the group; anticipate deviations from objectives/budgets and recommend corrective and preventive actions; Participate in performance improvement, for example through cost optimization, material consumption, and inventory levels (rotation, obsolescence); develop and implement industrial accounting in close collaboration with Operations and the IT Department (support ERP development); participate in the preparation of monthly activity reports (monitoring and evolution of production costs and performance indicators); participate in preparing responses to group inquiries; conduct ad-hoc missions at the request of management; validate investment requests; carry out all missions within the scope of your duties or at the request of your supervisor; *Non-exhaustive list. Required skills and knowledge: You hold a Master's degree (BAC+5) from a higher education institution specializing in finance or auditing and management control; you have a minimum of 3 years of experience in a similar position; You possess the following skills/knowledge: Proficiency in Microsoft Office, particularly Excel; Comfortable working with databases; Strong analytical, precision, and rigor skills; Excellent synthesis skills; Solid knowledge of accounting and industrial management control; Margin variance analysis; Mastery of operating cycles (purchasing and sales statistics, inventory valuation); Mastery of short- and medium-term performance forecasting. Your interpersonal skills, curiosity, and ability to be proactive and innovative will enable you to successfully carry out your duties and thrive in this role.</div></section><section>Desired Candidate ProfileYou hold a Master's degree (BAC+5) from a higher education institution specializing in finance or auditing and management control; You have a minimum of 3 years' experience in a similar position; You possess the following skills/knowledge: Proficiency in Microsoft Office, particularly Excel; Comfortable working with databases; Strong analytical, precision, and rigor skills; Ability to synthesize information; Solid knowledge of accounting and industrial management control; Margin variance analysis; Mastery of operating cycles (purchasing and sales statistics, inventory valuation); Mastery of short- and medium-term performance forecasting. Your interpersonal skills, curiosity, and ability to be proactive and innovative will enable you to successfully carry out your duties and thrive in this role.</section>

Electrical/Mechanical Technician

Molding Engineer

Gas Pipeline Construction Supervisor

Senior General Installation Engineer

Lawyer

Project Leader

Process Technician

Manufacturing Technician

Production Assistant

Manufacturing Technician

Production Supervisor

IT Technician

Business Development Manager

FAI Technician

Industrial Maintenance and New Works Coordinator

Industrial Maintenance Technician

Industrial Maintenance Technician

Quality Engineer

Buyer

Controller

Site Owners

Employers

Job Seekers

Oil

Receive email alerts for Oil jobs